Search results

There is a charcoal canister under the gunwale too, for inspection. Always a good time while you're in there checking, to put some tef-gel on your sending unit screws since it is so early in its life. You could Life-seal your pie plates when you are done, to better keep the water off your...

I would rather believe than not believe overheat alarms. Especially on both engines. I doubt the teeny trim tabs could put the engines in a position to overheat, especially with the bracket setback. Please follow-up if you (hopefully!) find the smoking gun. The fact that the dealer was able to...

I understand it is not what you asked for, but have you considered a coffin box? Extra seating, extra storage, you could put a decent sized cooler in there for smaller fish or use it all for bigger fish, without putting water below your deck. Nice ones are expensive, but would be worth it (to...

Enough to stand on for sure, assuming it is sound. I have had 350 to 450 pounds on my '19 2320 roof plenty of times, just chilling, and I have jumped off the top plenty, at 190.

I'm pretty beat from a long trip yesterday, so doing a knifeholder mod of some sort today. This thing is solid as a rock (even though the livewell through-bolts are barely snug) due to the gasket material conforming to the textured surfaces.

So after a month and a half, there is a distinct difference in the feel and smell of the cabin. Still fresh, zero mold. Cost was less than 100 bucks to seal it from outside air (when door is closed). BTW, there are 2- 6 to 10 square inch holes that lead to the anchor locker in the outer upper...

Ever notice your ice getting nuked really fast? I did several times, so I cut additional 3/4 inch rubber and lined the box. I drilled the drain plug so melt water would just barely drain and not slosh around. Ice lasts for days. Fixed it, or so I thought. Welp, went fishing last week, and when...

I THINK it's a Parker...

Yes, wish you the best. I couldn't open your photos.

Just a suggestion. Bite the bullet once and buy a knob. It stinks for sure. Put a drop of blue Loctite on each knob and tighten juuuust enough to eliminate slack and vibrations. Check out post 28 in the thread below. I haven't touched those knobs in 3 or 4 years. Takes seconds to put both...

Boat looks great. Is the lower unit all the way out of the water, and is there any growth on the bottom? Thank you.

Rewatched the video, that dude was lucky. It leads me to believe the boat was moving pretty fast since it almost "ran us down," but when they got control they were right at the guy? Hmmm.

Welp, there goes the lanyard exemption for pilot houses. I never really run on plane from the cockpit, but I need to re-read the rule.

I bought heavy brackets for the rod holders with the intention of stainless but they were crazy high, so I just used zinc and sprayed them with CRC anti corrosion spray . Not only does it add the bait tank, but 6 sturdy rod holders for the trailer trip, 2 cup holders and 2 tackle trays. It...

Maybe connect the panels together on the inside with hinges, and put a handle(s) of some sort high on the front face. You can then pull them off with one motion. Or cut two oval holes that match (when folded) near the top adjacent edges, then you can lift both out with one hand, they will stay...

No, but I will pop it down out of the garage tomorrow and snap a few. It is this one. Note it doesn't come with hinges for the lid or any fittings. I may have even bought a few drain plugs. 100% worth it to me though, to be removable. We have been spade, seabass and flounder fishing...

To the nearest 1/8"... that's a joke. I can't help it, chronic experimenting hack.

I used a 48" aluminum ruler from Ace. Just had to get the correct length bolt. I secured to bolt first with a nut to provide some offset, and then used acorn nuts on the ruler itself. Rev 0 without the spacing off the toe kick was buzzy at certain engine RPMs and the lower corners were...

I like it. I was just concerned about trim. That is a great option. Since I started using the transom livewell pressurized, it kept 36 croakers alive. I haven't needed it since, even though the transom livewell "should" be too small on paper.