My '95 2530

warthog5 · Sep 26, 2012

Guess this is where I'll load the server done from now on with this boat. I can't leave it alone....I have to cut on it.

So here's the 1st cutting.

Before:

Thinking about where I wanted it. Kevin's 10in is shifted toward the STB side.

A few things entered into my head.
1] The wiring was already tight all down the boat,so I'd have to cut every tie wrap.
2] If someone else is running the boat it is farther to reach the buttons for me to make a adjustment.
3] The way that pull tab stuck out for the cover.

Final decision:

To Late now.

warthog5 · Sep 26, 2012

Both Fuel sending units were defective.

This is showing the old float type and the new Haden unit.

I hate those Spade terminals on the Gnd.

No screws were broken. New Socket Head fasteners installed with Tef-Gel

warthog5 · Sep 26, 2012

Having problems with PhotoBucket. Hmmmmmmm!

All pix's were resized to 640 X 480. And the last one is weird with that 4th pix being a double, yet it doesn't show when I try to edit it.

miky2884 · Sep 26, 2012

Much better location for the chart plotter! Looking forward to following your upgrades

warthog5 · Sep 26, 2012

Yea....Where it was you had to reach, cables hanging down the the V berth overhead.

and it blocked view out the Port windshield. I was lucky enough to pick up a cut pattern locally.

Bryan 2530 · Sep 26, 2012

Very nice!!

Did the magnetic card door screw up the compass?? Mine did by a few degrees.

Looking forward to many more!! :mrgreen:

warthog5 · Sep 26, 2012

I'll check that. It's just sitting in the hole right now. So I can just note it and lift it out to see if any change.

Went to all the tool supply shops in town + the box stores looking for a 3 3/8in holesaw today. Grainger will have one tomorrow to cut the new gauge holes.

warthog5 · Sep 26, 2012

Wow.....Yes altered the Compass 6deg to the South.

Megabyte · Sep 26, 2012

Nice work!

GW204 did all of my cutting on the helm while I held the vacuum underneath.

I had just had hand surgery so he was a *huge* asset!

Checked my compass before, and then after, and it did not change.
Guess I got lucky!

Nice work Bobby! 8)

Oyster · Sep 26, 2012

So you need a Garmin for your new driveway queen. :lol: :lol:

Nice project and boat, good luck with getting it the way you want it.

miky2884 · Sep 26, 2012

Yea i had the same problem off about 4 degrees. Shame on garmin for putting a magnet in that door. So many other options they could have gone with. Still best electronics going in my oppinion.

DaleH · Sep 26, 2012

Nice work on that install Bobby!

Megabyte":2f884csa said:
GW204 did all of my cutting on the helm while I held the vacuum underneath.
I had just had hand surgery so he was a *huge* asset!

I grew up as a locksmith, as my Dad was a 2nd generation one ... and I paid for college expenses by installing deadbolts on the doors, paid $10 per install. I'd tape a large paper bag (large type with handles) around both sides of the door, just below the d-bolt location, to catch all the dust and debris from the hole saw ... as we didn't have to sweep per se, but had to make sure all wood/metal pieces were caught. Let's just say I was making $30-40 an hour @ 19-years old

!

So ... if no 2nd helper like our good Capt Kevin is around to catch your debris ... think about the paper bag trick! Oh, I also prefer cutting frp with a downward cutting 'laminate' jigsaw blade ... super clean cut and that too forces all of the debris into the collection bag

.

warthog5 · Sep 26, 2012

I cut this all with a air saw. It's narrow and extremely agile to maneuver.

miky2884 · Sep 27, 2012

Bryan is a master with the roto zip have him come down and help you. :roll:

warthog5 · Sep 27, 2012

I actually own a Roto Zip. Haven't used it in a Loooong time. I have found better tools to do the job with. A Roto Zip is nothing but a Tiny router. They throw Crap EVERYWHERE! Including fiberglass dust on you. I try to do everything I can to NOT do that.

Got the 3 3/8in Holesaw today. Gauges are all in. By the way a 2 1/16in holesaw is what you really want for 2in gauges. It slips right in perfect....No fuss...No Muss.

Hourmeter installed under the key switch. Down and out of the way where it should have been put. It also keeps the Tick Tocking of the clock out of your ears. There is no reason to have that gauge in your face all the time. It is a maintenance gauge.

Megabyte · Sep 27, 2012

warthog5":3tnw304s said:

Now that is looking sporty!

Bryan 2530 · Sep 27, 2012

Very nice.

warthog5 · Sep 28, 2012

I hooked the gauge wires back up.....Not the routing I want yet. Turned the Master switch on......Squeezed the ball a bunch of times after the motor was tilted down [manually] Turned the key and it made about 4 revolutions and fired up. That sucker is loud and it was 7:00 in the morning so I shut it down after 1 1/2min. I’ll fire it again later.

DaleH · Sep 28, 2012

Looking good Bobby! To keep that 250hp running good, somewhere on here we have a the info from Bill Grannis as a DIY "How To" for keeping the O2 sensor on that puppy clean and runing well.

warthog5 · Sep 29, 2012

Thanks....Today my Son & Granddaughters Ha! unbolt the motor to attack the 2 other bolts on the tilt/trim motor. Acetylene torch is on hand for heat.

Yesterday was a sad day.

Got word back why my '99 DF-70 Suzuki for my Flounder boat would not idle.
This boat sat in the water and owned by a marina was used as a pusher boat and general stuff. It has less than 100hrs on the motor. But it was never flushed. The inside of the motor is eaten up. One rotted hole allowing water into #1 cyl is the culprit of the no idle. There is another hole beginning. This no idle has gotten worse. At first I thought it was just a cold naturered little bugger. But the last night out [last Saturday] it didn't leave us stranded, but was a bitch to power load, as it would stall. So I took it to Posiner Marine for diagnosis. Now I need a new motor. It's not worth investing any money in.

$10K out the door for a '12 DF-90A.

Here's the build on it. :
http://www.aluminumalloyboats.com/viewt ... under+Boat

My '95 2530

Help Support Classic Parker Boat Forum:

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Member

Well-known member

FOUNDER of Classic Parker Forum

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

FOUNDER of Classic Parker Forum

Well-known member

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!